Unterschiede

Hier werden die Unterschiede zwischen zwei Versionen angezeigt.

Link zu dieser Vergleichsansicht

Beide Seiten der vorigen Revision Vorhergehende Überarbeitung
circuit_design:uebung_3.3.2 [2021/11/27 23:29]
tfischer 		circuit_design:uebung_3.3.2 [2023/03/28 10:12] (aktuell)
mexleadmin
Zeile 2: Zeile 2:
  
 In this exercise, the same question should be assumed as in exercise 3.3.1. This time, however, the influence of the impedance converter on the sensor signal is to be analyzed. The signal curve of the ECG voltage must be simulated by the voltage source. To do this, select ''Piecewise linear'' (3rd from the right) as the voltage source and use the curve below.\\ In this exercise, the same question should be assumed as in exercise 3.3.1. This time, however, the influence of the impedance converter on the sensor signal is to be analyzed. The signal curve of the ECG voltage must be simulated by the voltage source. To do this, select ''Piecewise linear'' (3rd from the right) as the voltage source and use the curve below.\\
-In addition, the influence on the current (= output resistor of the sensor) must be taken into account. To do this, insert a resistor with $20 M\Omega$ directly in front of the non-inverting inputs.+In addition, the influence on the current (= output resistor of the sensor) must be taken into account. To do this, insert a resistor with $20 ~\rm M\Omega$ directly in front of the non-inverting inputs.
  
 ++++Instruction| ++++Instruction|
-<code>+<sxh>
  
 120ms, 0 120ms, 0
Zeile 11: Zeile 11:
 200ms, 0 200ms, 0
 260ms, 0 260ms, 0
-270ms, -0.2m +270ms,-0.2m 
-320m,1m +320ms, 1m 
-340m,-0.3m +340ms,-0.3m 
-350m,0 +350ms, 0 
-440ms,0 +440ms, 0 
-520ms,0.1m+520ms, 0.1m
 600ms, 0 600ms, 0
 820ms, 0 820ms, 0
Zeile 23: Zeile 23:
 960ms, 0 960ms, 0
 970ms, -0.2m 970ms, -0.2m
-1020m,1m +1020ms, 1m 
-1040m,-0.3m +1040ms,-0.3m 
-1050m,0 +1050ms, 0 
-1140ms,0 +1140ms, 0 
-1220ms,0.1m+1220ms, 0.1m
 1300ms, 0 1300ms, 0
 1400ms, 0 1400ms, 0
  
-</code>+</sxh>
  
 ++++ ++++
  
-  - Now simulate the time course for $0 s$ to $2 s$ with "Use initial conditions".+  - Now simulate the time course for $0 ~\rm s$ to $2 ~\rm s$ with "Use initial conditions".
   - What is the only difference in the output signals? (note y-axis)   - What is the only difference in the output signals? (note y-axis)
   - For a more realistic operational amplifier, 3 additional current sources and an additional voltage source must be taken into account in the equivalent circuit diagram (see <imgref pic3_3_2>). In Tina, the values ​​of these current sources can be viewed in the specifications of the simulated operational amplifier (double click on the OPV in ''Circuit'' >> ''Type…'' >> ''Model Parameters''). The analysis of the entire circuit (including the equivalent circuit diagram) is not to be considered here. It is assumed that the "input bias current" of the operational amplifier is the decisive value. \\ Compare the values ​​of the different operational amplifiers.   - For a more realistic operational amplifier, 3 additional current sources and an additional voltage source must be taken into account in the equivalent circuit diagram (see <imgref pic3_3_2>). In Tina, the values ​​of these current sources can be viewed in the specifications of the simulated operational amplifier (double click on the OPV in ''Circuit'' >> ''Type…'' >> ''Model Parameters''). The analysis of the entire circuit (including the equivalent circuit diagram) is not to be considered here. It is assumed that the "input bias current" of the operational amplifier is the decisive value. \\ Compare the values ​​of the different operational amplifiers.
   - To simplify matters, think about the additional input voltage that results from the current of a single bias current source at the sensor resistor.   - To simplify matters, think about the additional input voltage that results from the current of a single bias current source at the sensor resistor.
  
-<WRAP right><panel type="default"> <imgcaption pic3_3_2 | real OPV> </imgcaption> {{drawio>pic3_3_2 }} </panel></WRAP>+<WRAP right><panel type="default"> <imgcaption pic3_3_2 | real OPV> </imgcaption> {{drawio>pic3_3_2.svg}} </panel></WRAP>
  
 </WRAP></WRAP></panel> </WRAP></WRAP></panel>