Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision		 Previous revision
lab_electrical_engineering:rectangular-to-triangle_signal_conversion_integrator [2026/06/17 12:27] – mexleadminlab_electrical_engineering:rectangular-to-triangle_signal_conversion_integrator [2026/06/17 13:21] (current) – mexleadmin
Line 4: Line 4:
  
 The operation of an OPV in the linear operating range can be enforced by means of circuitry by feeding back the output signal, i.e., returning it to the inverting input (- input). In the circuit shown, the negative feedback is provided by a capacitor.\\ The operation of an OPV in the linear operating range can be enforced by means of circuitry by feeding back the output signal, i.e., returning it to the inverting input (- input). In the circuit shown, the negative feedback is provided by a capacitor.\\
-\\ 
 \\ \\
 <wrap left> {{drawio>integrator_circuit.svg}}</wrap>\\ <wrap left> {{drawio>integrator_circuit.svg}}</wrap>\\
Line 17: Line 16:
 $u_\mathrm{a}=-u_C=-\frac{1}{C}\int i_\mathrm{C}\,dt=-\frac{1}{RC}\int u_\mathrm{e}\,dt$\\ $u_\mathrm{a}=-u_C=-\frac{1}{C}\int i_\mathrm{C}\,dt=-\frac{1}{RC}\int u_\mathrm{e}\,dt$\\
 ~~CLEARFIX~~ ~~CLEARFIX~~
- 
 The integrated input voltage appears at the output. The product of resistance and capacitance has the character of a time constant: The integrated input voltage appears at the output. The product of resistance and capacitance has the character of a time constant:
  
 $T_\mathrm{i}=RC$\\ $T_\mathrm{i}=RC$\\
-\\ 
 \\ \\
 <wrap left> {{drawio>integrator_u-t-diagramme.svg}}\\ <wrap left> {{drawio>integrator_u-t-diagramme.svg}}\\
Line 31: Line 28:
 The figure shows the output voltage of an integrator with a square wave voltage at the input. The output voltage at the start $u_\mathrm{a}(t=0)$ depends on the charge state of the capacitor when switched on.\\ The figure shows the output voltage of an integrator with a square wave voltage at the input. The output voltage at the start $u_\mathrm{a}(t=0)$ depends on the charge state of the capacitor when switched on.\\
  
-~~CLEARFIX~~+~~PAGEBREAK~~ ~~CLEARFIX~~
 ====Experimental Tasks==== ====Experimental Tasks====
  
 To analyze the behavior of the integrator, the following circuit is used:\\  To analyze the behavior of the integrator, the following circuit is used:\\ 
-\\  
-\\  
 <wrap left> <wrap left>
 {{drawio>integrator_experiment.svg}} {{drawio>integrator_experiment.svg}}
Line 51: Line 46:
 ~~CLEARFIX~~ ~~CLEARFIX~~
  
-  - Calculate the time constant $T_\mathrm{i}$ of the integrator from the given values. \\ \\ \\ \\ \\ \\ \\  +  - Calculate the time constant $T_\mathrm{i}$ of the integrator from the given values. \\ \\ \\ \\ \\ \\ \\ \\ 
-  - Assumption: the capacitor is initially uncharged. A voltage $u_\mathrm{e}=+3~V$ is applied to the input. \\ How long does it take for the output voltage to reach $u_\mathrm{Tr}=-3~V$? Document your calculation. \\ \\ \\ \\ \\ \\ \\  +  - Assumption: the capacitor is initially uncharged. A voltage $u_\mathrm{e}=+3~V$ is applied to the input. \\ How long does it take for the output voltage to reach $u_\mathrm{Tr}=-3~V$? Document your calculation. \\ \\ \\ \\ \\ \\ \\ \\ \\ \\ \\ \\ \\ 
-  - Roughly sketch the voltage curves that you expect at the TR output when you apply a bipolar square wave signal to the $u_\mathrm{e}$ input.\\ \\ **Output TR**\\ \\ <wrap left>{{drawio>oscilloscope_screen.svg}}</wrap>\\ \\ \\ Channel 1:$\frac {Volt}{Div}=$\\ \\ \\ Time basis: $\frac {T}{Div}=$ ~~CLEARFIX~~ +  - Roughly sketch the voltage curves that you expect at the TR output when you apply a bipolar square wave signal to the $u_\mathrm{e}$ input.\\ \\ \\ **Output TR**\\ \\ <wrap left>{{drawio>oscilloscope_screen.svg}}</wrap>\\ \\ \\ Channel 1:$\frac {Volt}{Div}=$\\ \\ \\ Time basis: $\frac {T}{Div}=$ ~~CLEARFIX~~ \\ 
-  - Build the circuit on the MEXLE-board. Make sure that the jumper at the bottom of the op-amp is set to the left so that the op-amp is supplied with +/- 3V. Connect channel 1 on the oscilloscope to $U_\mathrm{e}$ and channel 2 to TR. Connect the function generator to the $U_\mathrm{e}$ input. Set to square wave (bipolar) with a frequency of 3kHz and a voltage of 3 V (amplitude). Switch on the power supply. Take a photo of the oscilloscope screen image. \\ \\ \\ **C1 = 10 nF, f = 3 kHz**\\ \\ <wrap left>{{drawio>oscilloscope_screen.svg}}</wrap>\\ \\ \\ Channel 1: $\frac {Volt}{Div}=$\\ \\ Channel 2: $\frac {Volt}{Div}=$\\ \\ \\ Time basis: $\frac {T}{Div}=$ ~~CLEARFIX~~ +  - Build the circuit on the MEXLE-board. Make sure that the jumper at the bottom of the op-amp is set to the left so that the op-amp is supplied with +/- 3V. Connect channel 1 on the oscilloscope to $U_\mathrm{e}$ and channel 2 to TR. Connect the function generator to the $U_\mathrm{e}$ input. Set to square wave (bipolar) with a frequency of 3kHz and a voltage of 3 V (amplitude). Switch on the power supply. \\ \\ \\ **C1 = 10 nF, f = 3 kHz**\\ \\ <wrap left>{{drawio>oscilloscope_screen.svg}}</wrap>\\ \\ \\ Channel 1: $\frac {Volt}{Div}=$\\ \\ Channel 2: $\frac {Volt}{Div}=$\\ \\ \\ Time basis: $\frac {T}{Div}=$ ~~CLEARFIX~~ 
-  - Compare your measurement with the calculation from part 2 and the forecast from part 3. Explain your result. \\ \\ \\ \\ \\ \\ \\ \\ \\ \\ \\ +  - Compare your measurement with the calculation from part 2 and the forecast from part 3. Explain your result. \\ \\ \\ \\ \\ \\ \\ \\ \\ \\ 
  
 <WRAP hide> <WRAP hide>