Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision		 Previous revision
lab_electrical_engineering:rectangular-to-triangle_signal_conversion_integrator [2026/06/17 12:44] – mexleadminlab_electrical_engineering:rectangular-to-triangle_signal_conversion_integrator [2026/06/17 13:21] (current) – mexleadmin
Line 28: Line 28:
 The figure shows the output voltage of an integrator with a square wave voltage at the input. The output voltage at the start $u_\mathrm{a}(t=0)$ depends on the charge state of the capacitor when switched on.\\ The figure shows the output voltage of an integrator with a square wave voltage at the input. The output voltage at the start $u_\mathrm{a}(t=0)$ depends on the charge state of the capacitor when switched on.\\
  
-~~CLEARFIX~~+~~PAGEBREAK~~ ~~CLEARFIX~~
 ====Experimental Tasks==== ====Experimental Tasks====
  
Line 48: Line 48:
   - Calculate the time constant $T_\mathrm{i}$ of the integrator from the given values. \\ \\ \\ \\ \\ \\ \\ \\   - Calculate the time constant $T_\mathrm{i}$ of the integrator from the given values. \\ \\ \\ \\ \\ \\ \\ \\
   - Assumption: the capacitor is initially uncharged. A voltage $u_\mathrm{e}=+3~V$ is applied to the input. \\ How long does it take for the output voltage to reach $u_\mathrm{Tr}=-3~V$? Document your calculation. \\ \\ \\ \\ \\ \\ \\ \\ \\ \\ \\ \\ \\   - Assumption: the capacitor is initially uncharged. A voltage $u_\mathrm{e}=+3~V$ is applied to the input. \\ How long does it take for the output voltage to reach $u_\mathrm{Tr}=-3~V$? Document your calculation. \\ \\ \\ \\ \\ \\ \\ \\ \\ \\ \\ \\ \\
-  - Roughly sketch the voltage curves that you expect at the TR output when you apply a bipolar square wave signal to the $u_\mathrm{e}$ input.\\ \\ **Output TR**\\ \\ <wrap left>{{drawio>oscilloscope_screen.svg}}</wrap>\\ \\ \\ Channel 1:$\frac {Volt}{Div}=$\\ \\ \\ Time basis: $\frac {T}{Div}=$ ~~CLEARFIX~~ \\ \\+  - Roughly sketch the voltage curves that you expect at the TR output when you apply a bipolar square wave signal to the $u_\mathrm{e}$ input.\\ \\ \\ **Output TR**\\ \\ <wrap left>{{drawio>oscilloscope_screen.svg}}</wrap>\\ \\ \\ Channel 1:$\frac {Volt}{Div}=$\\ \\ \\ Time basis: $\frac {T}{Div}=$ ~~CLEARFIX~~ \\
   - Build the circuit on the MEXLE-board. Make sure that the jumper at the bottom of the op-amp is set to the left so that the op-amp is supplied with +/- 3V. Connect channel 1 on the oscilloscope to $U_\mathrm{e}$ and channel 2 to TR. Connect the function generator to the $U_\mathrm{e}$ input. Set to square wave (bipolar) with a frequency of 3kHz and a voltage of 3 V (amplitude). Switch on the power supply. \\ \\ \\ **C1 = 10 nF, f = 3 kHz**\\ \\ <wrap left>{{drawio>oscilloscope_screen.svg}}</wrap>\\ \\ \\ Channel 1: $\frac {Volt}{Div}=$\\ \\ Channel 2: $\frac {Volt}{Div}=$\\ \\ \\ Time basis: $\frac {T}{Div}=$ ~~CLEARFIX~~   - Build the circuit on the MEXLE-board. Make sure that the jumper at the bottom of the op-amp is set to the left so that the op-amp is supplied with +/- 3V. Connect channel 1 on the oscilloscope to $U_\mathrm{e}$ and channel 2 to TR. Connect the function generator to the $U_\mathrm{e}$ input. Set to square wave (bipolar) with a frequency of 3kHz and a voltage of 3 V (amplitude). Switch on the power supply. \\ \\ \\ **C1 = 10 nF, f = 3 kHz**\\ \\ <wrap left>{{drawio>oscilloscope_screen.svg}}</wrap>\\ \\ \\ Channel 1: $\frac {Volt}{Div}=$\\ \\ Channel 2: $\frac {Volt}{Div}=$\\ \\ \\ Time basis: $\frac {T}{Div}=$ ~~CLEARFIX~~
-  - Compare your measurement with the calculation from part 2 and the forecast from part 3. Explain your result. \\ \\ \\ \\ \\ \\ \\ \\ \\ \\ \\ +  - Compare your measurement with the calculation from part 2 and the forecast from part 3. Explain your result. \\ \\ \\ \\ \\ \\ \\ \\ \\ \\ 
  
 <WRAP hide> <WRAP hide>