An automotive engineer is testing the electrical system of a passenger car. The vehicle has a 12 V battery, interior lighting, a temperature sensor, and a rear window heater. During vehicle development, the engineer must verify electrical components using resistance measurements, Ohm's law, series and parallel circuits, Kirchhoff's laws, and the behavior of a non-linear load.
Resistance is defined by voltage and current:
$$ R = \frac{U}{I} $$
A constant supply voltage is available for the experiment. This raises the following questions:
To answer these questions, different circuits are investigated: the Mesh-set, Set of nodes and a light bulb circuit for nonlinear resistors.
Procedure for resistance measurement:
There are different types of resistance measurement:
The resistances can also be determined by measuring the current/voltage.
Ohm's law: In an electrical circuit, the current increases with increasing voltage and decreases with increasing resistance.
$$ I=\frac{U}{R} $$


Build the measuring circuit shown in figure 1 for each of the three resistors and set the voltage on the power supply to $~{\rm 12} ~{ V}$.

In every closed circuit and every mesh of the network, the sum of all voltages is zero!
Set the voltage on the power supply to $12~\rm V$ and measure this voltage precisely using a multimeter. Set up the measuring circuit shown in figure 2.
Add the voltage arrows and measure $U$, $U_{\rm 1}$ und $U_{\rm 2}$:
<tabcaption Table-4_mesh-set_V1 | Mesh set voltage mesurement> </tabcaption>
What is the mesh set here?
Check the formula with the measured values:
The resistors $R_{\rm 1}$ and $R_{\rm 2}$ connected in series form a voltage divider.
$$ \frac{U_1}{U_2} = $$
At each junction point, the sum of all incoming and outgoing currents is equal to zero!
Set the voltage on the power supply to $12~\rm V$ and measure the voltage accurately with a multimeter. In the first step, set up the measuring circuit shown in figure 3:
Draw the arrows for the directions of currents $I_{\rm 1}$ and $I_{\rm 2}$ in figure 4. The DC current measurement range must be set on both multimeter using the rotary switch. Then measure currents $I_{\rm 1}$ and $I_{\rm 2}$ and enter the measured values in table 4.
$$ \frac{I_1}{I_2} = $$
Switch the power supply back on and measure the current $I$. Enter its value in table 4.
$$ I=\frac{U}{R_{KP}} = $$
The voltage divider shown in figure 5 is in an unloaded state, as the entire current supplied by the power supply flows through the resistors $R_{\rm 1}$ and $R_{\rm 2}$ connected in series. A resistor parallel to $R_{\rm 2}$ loads the voltage divider.
Set the voltage on the power supply to $12 ~\rm V$ and measure the exact voltage with a multimeter. Set up the measuring circuit shown in figure 5.
For the connected load $R_{\rm L}$ = ${\rm 10} ~{\rm k\Omega}$, the voltage divider represents a voltage source. Like any voltage source, it has a source voltage (also called the original voltage) $U_{\rm 0}$ and an internal resistance $R_{\rm i}$. The internal resistance of a voltage divider considered as a voltage source results from the parallel connection of the divider resistors $R_{\rm 1}$ and $R_{\rm 2}$:
$$ R_i = R_1 || R_2 = \frac{R_1\cdot R_2}{R_1+R_2} $$
$$ R_i = $$
$$ U_0 = $$
The power $P_{\rm 0}$ supplied by the power supply can be calculated using the following equation:
$$ P_0 = U\cdot I_1$$
The power consumed by the load resistance can be determined using the following formula:
$$ P_L = R_L\cdot {I_2}^2$$
$$ U_{2, zero} = $$
$$ U_{2L} : $$
$$ I_2 : $$
All resistors examined so far are linear resistors, for which the characteristic curve $I=f(U)$ is a straight line, s. figure 6.
The resistance value of a linear resistor is independent of the current $I$ flowing through it or the applied voltage $U$.
Fig. 6: Characteristic curve of a linear resistor
With nonlinear resistors, there is no proportionality between current and voltage. The characteristic curve of such a resistor is shown in figure 7. With these resistors, we talk about static resistance ($R$) and dynamic (or differential) resistance ($r$). The static resistance is determined for a specific operating point: at a specific voltage, the current is read from the resistance characteristic curve.
The calculation is performed according to Ohm's law:
$$ R = \frac{U}{I} $$
The differential resistance around the operating point is calculated from the current difference caused by a change in the applied voltage:
$$ r = \frac{\Delta U}{\Delta I} $$
Fig. 7: Characteristic curve of a nonlinear resistor
A light bulb is examined as an example of a nonlinear resistor. Set up the measuring circuit shown in figure 8.
Fig. 8: Measuring circuit light bulb
Set the voltage on the power supply to the voltage values from table 5. Measure the corresponding current values and enter them in table 5.
Fig. 9: Characteristic curve light bulb