This is an old revision of the document!
TBD
-
- Fundamentals (conductors, semiconductors, insulators, doping, band model, intrinsic conductivity)
- Diodes (real characteristic curve, operating point, equivalent circuit)
- Zener diode
- LED
- Protective circuit with diodes
- Rectifier circuits (single-phase rectifier, center tap circuit, bridge rectifier, smoothing capacitor)
- Bipolar transistor (structure, designations, characteristic curve, characteristic values)
- Transistor as a switch (circuit, switching times and behavior)
- MOSFET (structure, comparison with bipolar transistor)
- Optional: Transistor as an amplifier
Block 11 — Semiconductor Fundamentals and Diodes
Learning objectives
- distinguish conductors, semiconductors, and insulators using the band model.
- explain intrinsic conduction, electron conduction, and hole conduction.
- explain how n-doping and p-doping change the number of mobile charge carriers.
- describe the formation of a pn junction and the depletion region.
- decide whether a diode is forward-biased or reverse-biased from \(u_{\rm AK}\).
- compare the ideal diode model, the constant-voltage model, and the piecewise-linear diode model.
- use the diode equation
\[ \begin{align*} i_{\rm D}=I_{\rm S}(T)\left({\rm e}^{\frac{u_{\rm AK}}{mU_{\rm T}}}-1\right) \end{align*} \] at a qualitative level.
- calculate simple diode operating points with a series resistor.
- identify basic diode types such as universal diodes, Z-diodes, and LEDs.
90-minute plan
- Warm-up (10 min):
- Why does a diode conduct in one direction but not in the other?
- Recall from EEE1: voltage, current direction, power, and resistors.
- Recall from EEE2: transient overvoltages at inductive loads will later need diode protection.
- Core concepts (55 min):
- Conductors, semiconductors, insulators, and the band gap.
- Intrinsic conduction, electron conduction, hole conduction.
- Doping: n-type and p-type material.
- pn junction, depletion region, diffusion voltage.
- Diode operation in forward and reverse direction.
- Ideal and real diode characteristics.
- Practical diode models for circuit calculations.
- Practice (20 min):
- Determine diode polarity and conduction state.
- Calculate current with a constant-voltage diode model.
- Estimate differential resistance at a given operating point.
- Compare ideal and real diode assumptions.
- Wrap-up (5 min):
- Key messages: pn junction, forward/reverse bias, current limiting, diode models.
- Preview: rectifiers, smoothing, protection circuits, LEDs, and Z-diode stabilizers in Block 12.
Conceptual overview
- A semiconductor is neither a good conductor nor a perfect insulator. Its conductivity can be controlled by material, temperature, light, and doping.
- A diode is a pn junction with two terminals:
- anode A on the p-side,
- cathode K on the n-side.
- In forward direction, the external voltage reduces the depletion region and current can flow.
- In reverse direction, the depletion region becomes wider and only a very small leakage current flows, until breakdown occurs.
- A diode is nonlinear. It is not a resistor.
- In circuits, diode current must usually be limited by another component, often a resistor.
Scope of this block
This block explains why diodes behave as they do and how we model them.
Diode applications such as
- rectifiers,
- smoothing capacitors,
- freewheeling diodes,
- input protection circuits,
- LED circuits,
- Z-diode voltage stabilizers
are continued in Block 12.
Core content
Introductory Example
Microcontrollers often have many pins that evaluate signals between $0...5~\rm V$ as a digital signal. However, the input signal can be disturbed during transmission by small coupled pulses, e.g. from HF sources like mobile phones. This interference can cause the signal to leave the permitted voltage range of approx. $-0.5...5.5~\rm V$ and thus destroy the logical unit.
To prevent such destruction, an over-voltage protection circuit consisting of diodes is installed (see e.g. ATmega 328). In case of an over-/under-voltage one of the diodes becomes conductive and lowers the input voltage by the resulting current. In the simulation, it can be seen that the interference on the input side can be reduced to an acceptable, low level by the protection circuit.
This chapter explains why a diode becomes conductive at a certain voltage, what has to be considered when using diodes, and which different types of diodes are available.
For the protection of digital interfaces that leave the device housing (e.g. USB), additional separate ICs are used that support this protection of the data processing chips. These protection diode ICs suppress the short-time voltages and are called Transient Voltage Suppressor or TVS diodes. Typical TVS ICs are NUP2301 or for USB NUP4201.
Further reading
- An introductory is available at electronics-tutorials
A short quantum view: why energy bands matter
Materials differ strongly in their specific resistance \(\rho\).
Why we need a band model
The simple circuit view says: conductors conduct, insulators block, semiconductors are somewhere in between. To understand why semiconductors can be controlled so well, we need a short look at the energy of electrons in a solid.
In a single atom, electrons can only have certain discrete energies (figure 2 1a and 1b). This is one result of quantum physics. A simple picture is the Bohr model: electrons are not allowed to move on arbitrary paths, but only on certain allowed energy levels.
In a solid, many atoms are very close together (figure 2 2a and 2b). Their individual energy levels interact and broaden into energy bands.
The two most important bands are:
- the valence band: the highest occupied band. Electrons here are still bound in the crystal.
- the conduction band: the next higher band. Electrons here can move through the crystal and contribute to current.
The energetic distance between them is the band gap \(E_{\rm g}\).
\[ \begin{align*} E_{\rm g} = W_{\rm conduction~band} - W_{\rm valence~band} \end{align*} \]
For semiconductors, the band gap is small enough that some electrons can be lifted from the valence band into the conduction band.
| Material type | Band model | Electrical behavior |
|---|---|---|
| conductor | conduction band available or overlapping | many mobile charge carriers |
| semiconductor | small band gap, typically a few \({\rm eV}\) | conductivity can be controlled |
| insulator | large band gap | almost no mobile charge carriers |
- light, i.e. photons,
- lattice vibrations, i.e. thermal energy or phonons.
When an electron reaches the conduction band, it leaves behind a missing electron in the valence band. This missing electron behaves like a positive mobile charge carrier and is called a hole.
\[ \begin{align*} \text{energy input} \quad\Rightarrow\quad \text{electron-hole pair} \end{align*} \]
The opposite process is called recombination:
\[ \begin{align*} \text{electron}+\text{hole} \quad\Rightarrow\quad \text{released energy}. \end{align*} \]
Analogy: soccer stadium with two tribunes
Imagine a soccer stadium with two tribunes.
- The lower tribune is close to the field and very popular. It is normally fully booked. This is the valence band.
- The upper tribune is farther away and less attractive. To get there, a person needs an extra “energy ticket”. This is the conduction band.
- The required energy ticket is the band gap \(E_{\rm g}\).
If one person receives enough energy, they move from the full lower tribune to the upper tribune. Now the person upstairs can move around more freely, like an electron in the conduction band.
At the same time, an empty seat remains in the lower tribune. When neighboring people move into that empty seat, the empty seat itself seems to move. This moving empty seat is the analogy for a hole.
Intrinsic conduction, electrons, and holes
In a pure semiconductor, some electrons can gain enough energy to leave their bonds. Then
- The electron becomes mobile in the conduction band.
- A 'missing electron' (technically: a defect electron or a hole) remains in the valence band.
- This hole behaves like a positive mobile charge carrier.
- electrons with negative charge,
- holes with positive effective charge.
At room temperature, only a very small fraction of thermal vibrations has enough energy to generate such electron-hole pairs in pure silicon. Nevertheless, this already creates measurable intrinsic conduction.
Doping: n-type and p-type semiconductors
Doping increases the number of mobile charge carriers much more effectively:
- n-doping adds donor atoms and therefore additional mobile electrons,
- p-doping adds acceptor atoms and therefore additional mobile holes.
Doping means adding a very small amount of foreign atoms to the semiconductor crystal.
The pn junction
A diode is formed when p-doped and n-doped regions meet.
At the junction:
- electrons diffuse from the n-side into the p-side,
- holes diffuse from the p-side into the n-side,
- electrons and holes recombine,
- a region with almost no mobile charge carriers forms.
This region is called the depletion region or space-charge region.
The depletion region behaves like an internal barrier. Without an external voltage, it prevents a large current.
Analogy: a door with a spring
The depletion region is like a spring-loaded door.
- In one direction, you push against the spring and can open the door.
- In the other direction, the spring pushes the door more firmly closed.
The diode behaves similarly: one polarity reduces the barrier, the other polarity increases it.
Forward and reverse operation
We define the diode voltage
\[ \begin{align*} u_{\rm AK}=u_{\rm A}-u_{\rm K}. \end{align*} \]
- \(u_{\rm AK}>0\): anode is more positive than cathode.
- \(u_{\rm AK}<0\): anode is more negative than cathode.
<tabcaption tab_diode_bias|Diode operation depending on \(u_{\rm AK}\)>
| Condition | Name | Effect on depletion region | Current |
|---|---|---|---|
| \(u_{\rm AK}>0\) | forward bias | depletion region becomes smaller | large current possible |
| \(u_{\rm AK}<0\) | reverse bias | depletion region becomes larger | only small leakage current, until breakdown |
\[ \begin{align*} \text{Positive Anode, Negative Is Cathode} \end{align*} \]
This helps to remember the forward direction of a diode.
Ideal diode model
The simplest model is the ideal diode.
\[ \begin{align*} \text{forward direction: } u_{\rm AK}=0,\quad i_{\rm D}>0 \end{align*} \]
\[ \begin{align*} \text{reverse direction: } i_{\rm D}=0,\quad u_{\rm AK}<0 \end{align*} \]
Engineering meaning
The ideal diode is useful for a first decision:
- Is the diode conducting?
- Is the diode blocking?
- Which path can current take?
It is too simple for accurate voltage and current calculations.
Real diode characteristic
A real diode has an exponential current-voltage characteristic.
\[ \begin{align*} \boxed{ i_{\rm D} = {\color{red}{I_{\rm S}(T)}} \left( {\rm e}^{\frac{{\color{blue}{u_{\rm AK}}}}{{\color{green}{mU_{\rm T}}}}} -1 \right) } \end{align*} \]
with
\[ \begin{align*} U_{\rm T}=\frac{kT}{e}. \end{align*} \]
<tabcaption tab_diode_equation_symbols|Symbols in the diode equation>
| Symbol | Meaning |
|---|---|
| \(I_{\rm S}(T)\) | reverse saturation current, strongly temperature-dependent |
| \(m\) | emission coefficient, typically \(1\ldots 2\) |
| \(U_{\rm T}\) | thermal voltage |
| \(k\) | Boltzmann constant |
| \(e\) | elementary charge |
| \(T\) | absolute temperature in \({\rm K}\) |
At room temperature, \(U_{\rm T}\) is approximately
\[ \begin{align*} U_{\rm T}\approx 26~{\rm mV}. \end{align*} \]
Typical values at \(25^\circ{\rm C}\):
<tabcaption tab_typical_diode_values|Typical diode values>
| Diode material | Approximate threshold voltage \(U_{\rm TO}\) | Reverse saturation current \(I_{\rm S}\) |
|---|---|---|
| silicon | \(\approx 0.7~{\rm V}\) | some \({\rm pA}\) |
| germanium | \(\approx 0.3~{\rm V}\) | some \(\mu{\rm A}\) |
Practical diode models for circuit calculation
For hand calculations we usually do not use the full exponential equation.
<tabcaption tab_diode_models|Diode models for circuit calculations>
| Model | Forward direction | Reverse direction | Use |
|---|---|---|---|
| ideal diode | \(u_{\rm AK}=0\) | \(i_{\rm D}=0\) | switching logic, first estimate |
| constant-voltage model | \(u_{\rm AK}\approx U_{\rm TO}\) | \(i_{\rm D}\approx 0\) | quick current calculations |
| piecewise-linear model | \(u_{\rm AK}\approx U_{\rm TO}+r_{\rm F}i_{\rm D}\) | \(i_{\rm D}\approx 0\) | more accurate operating point |
The differential forward resistance is
\[ \begin{align*} r_{\rm F} = \frac{\Delta U_{\rm F}}{\Delta I_{\rm F}}. \end{align*} \]
For large forward voltages compared with \(U_{\rm T}\), the diode equation leads approximately to
\[ \begin{align*} r_{\rm D} = \frac{{\rm d}u_{\rm D}}{{\rm d}i_{\rm D}} \approx \frac{mU_{\rm T}}{I_{\rm D}}. \end{align*} \]
\[ \begin{align*} [r_{\rm D}] = \frac{[U_{\rm T}]}{[I_{\rm D}]} = \frac{{\rm V}}{{\rm A}} = \Omega. \end{align*} \]
Operating point with a series resistor
A diode must usually be operated with a current-limiting element.
For the circuit
\[ \begin{align*} U_{\rm E} \rightarrow R \rightarrow D \end{align*} \]
the loop equation is
\[ \begin{align*} U_{\rm E} = U_R+U_{\rm D}. \end{align*} \]
With the constant-voltage model,
\[ \begin{align*} U_{\rm D}\approx U_{\rm TO}. \end{align*} \]
Therefore
\[ \begin{align*} I_{\rm D} \approx \frac{U_{\rm E}-U_{\rm TO}}{R}. \end{align*} \]
Z-diodes and LEDs as diode types
A Z-diode is operated in reverse breakdown. In its operating range, the diode voltage is approximately constant:
\[ \begin{align*} u_{\rm Z}\approx U_{\rm Z}. \end{align*} \]
The piecewise-linear model is
\[ \begin{align*} u_{\rm Z} \approx U_{\rm Z}+r_{\rm Z}i_{\rm Z}. \end{align*} \]
Z-diode preview
Z-diodes are useful for voltage limitation and voltage stabilization. The practical circuits are treated in Block 12.
An LED is a diode that emits light in forward direction. The required forward voltage depends on the semiconductor material and therefore on the color.
<tabcaption tab_led_forward_voltage|Typical LED forward voltages>
| LED color | Typical \(U_{\rm TO}\) |
|---|---|
| infrared | \(\approx 1.3~{\rm V}\) |
| red | \(\approx 1.6~{\rm V}\) |
| yellow | \(\approx 1.7~{\rm V}\) |
| green | \(\approx 1.8~{\rm V}\) |
| blue | \(\approx 3.2~{\rm V}\) |
Exercises
Exercise E1.1 Quick check: doping and charge carriers
Complete the table.
| Doping type | Typical dopant atom | Main mobile charge carrier | Dopant name |
|---|---|---|---|
| n-type | ? | ? | ? |
| p-type | ? | ? | ? |
| Doping type | Typical dopant atom | Main mobile charge carrier | Dopant name |
|---|---|---|---|
| n-type | phosphorus, arsenic, or antimony | electrons | donor |
| p-type | boron, aluminium, or indium | holes | acceptor |
N-type material has additional mobile electrons. P-type material has additional mobile holes.
The semiconductor as a whole remains approximately electrically neutral.
Exercise E2.1 Quick check: diode polarity
A diode has the anode voltage
\[ \begin{align*} U_{\rm A}=4.8~{\rm V} \end{align*} \]
and the cathode voltage
\[ \begin{align*} U_{\rm K}=4.1~{\rm V}. \end{align*} \]
- Calculate \(u_{\rm AK}\).
- Is the diode forward-biased or reverse-biased?
- For a silicon diode, is a noticeable current likely?
\[ \begin{align*} u_{\rm AK} = U_{\rm A}-U_{\rm K} = 4.8~{\rm V}-4.1~{\rm V} = 0.7~{\rm V}. \end{align*} \]
Since
\[ \begin{align*} u_{\rm AK}>0, \end{align*} \]
the diode is forward-biased.
For a silicon diode, \(0.7~{\rm V}\) is a typical forward voltage in the mA range. Therefore a noticeable current is likely.
Exercise E3.1 Quick check: current with the constant-voltage model
A silicon diode is connected in series with a resistor.
\[ \begin{align*} U_{\rm E}=5.0~{\rm V}, \qquad R=1.0~{\rm k}\Omega. \end{align*} \]
Use the constant-voltage model
\[ \begin{align*} U_{\rm D}\approx 0.7~{\rm V}. \end{align*} \]
Calculate the diode current \(I_{\rm D}\).
The voltage across the resistor is
\[ \begin{align*} U_R = U_{\rm E}-U_{\rm D} = 5.0~{\rm V}-0.7~{\rm V} = 4.3~{\rm V}. \end{align*} \]
Therefore
\[ \begin{align*} I_{\rm D} = \frac{U_R}{R} = \frac{4.3~{\rm V}}{1.0~{\rm k}\Omega} = 4.3~{\rm mA}. \end{align*} \]
Exercise E4.1 Quick check: differential diode resistance
A diode operates at
\[ \begin{align*} I_{\rm D}=10~{\rm mA}. \end{align*} \]
Assume
\[ \begin{align*} m=1, \qquad U_{\rm T}=26~{\rm mV}. \end{align*} \]
Estimate the differential diode resistance
\[ \begin{align*} r_{\rm D}\approx \frac{mU_{\rm T}}{I_{\rm D}}. \end{align*} \]
\[ \begin{align*} r_{\rm D} &\approx \frac{mU_{\rm T}}{I_{\rm D}} \\ &= \frac{1\cdot 26~{\rm mV}}{10~{\rm mA}} \\ &= 2.6~\Omega. \end{align*} \]
This is a small-signal resistance around the operating point. It is not the same as the large-signal ratio \(\frac{U_{\rm D}}{I_{\rm D}}\).
Exercise E5.1 Longer exercise: operating point with a piecewise-linear diode
A diode is connected in series with a resistor.
\[ \begin{align*} U_{\rm E}=12~{\rm V}, \qquad R=560~\Omega. \end{align*} \]
For the diode, use the piecewise-linear forward model
\[ \begin{align*} U_{\rm D} = U_{\rm TO}+r_{\rm F}I_{\rm D} \end{align*} \]
with
\[ \begin{align*} U_{\rm TO}=0.65~{\rm V}, \qquad r_{\rm F}=5.0~\Omega. \end{align*} \]
- Draw the loop equation.
- Calculate \(I_{\rm D}\).
- Calculate \(U_{\rm D}\).
- Calculate the diode power \(P_{\rm D}\).
- Compare briefly with the constant-voltage model \(U_{\rm D}=0.65~{\rm V}\).
The loop equation is
\[ \begin{align*} U_{\rm E} = RI_{\rm D} + U_{\rm D}. \end{align*} \]
Insert the piecewise-linear diode model:
\[ \begin{align*} U_{\rm E} = RI_{\rm D} + U_{\rm TO} + r_{\rm F}I_{\rm D}. \end{align*} \]
Thus
\[ \begin{align*} I_{\rm D} = \frac{U_{\rm E}-U_{\rm TO}}{R+r_{\rm F}}. \end{align*} \]
Insert the values:
\[ \begin{align*} I_{\rm D} &= \frac{12~{\rm V}-0.65~{\rm V}}{560~\Omega+5.0~\Omega} \\ &= \frac{11.35~{\rm V}}{565~\Omega} \\ &= 20.1~{\rm mA}. \end{align*} \]
The diode voltage is
\[ \begin{align*} U_{\rm D} &= U_{\rm TO}+r_{\rm F}I_{\rm D} \\ &= 0.65~{\rm V} + 5.0~\Omega\cdot 20.1~{\rm mA} \\ &= 0.65~{\rm V}+0.101~{\rm V} \\ &= 0.751~{\rm V}. \end{align*} \]
The diode power is
\[ \begin{align*} P_{\rm D} = U_{\rm D}I_{\rm D} = 0.751~{\rm V}\cdot 20.1~{\rm mA} = 15.1~{\rm mW}. \end{align*} \]
With the constant-voltage model,
\[ \begin{align*} I_{\rm D} = \frac{12~{\rm V}-0.65~{\rm V}}{560~\Omega} = 20.3~{\rm mA}. \end{align*} \]
The difference is small here because \(r_{\rm F}\ll R\).
Common pitfalls
- Thinking a diode is just a resistor: A diode is nonlinear. The ratio \(U/I\) is not constant.
- Forgetting current limitation: A forward-biased diode needs a current-limiting component.
- Treating \(0.7~{\rm V}\) as exact: The forward voltage depends on current, temperature, and semiconductor material.
- Mixing anode and cathode: Current flows easily from anode to cathode when the diode is forward-biased.
- Ignoring reverse limits: Real diodes have maximum reverse voltage. LEDs often tolerate only small reverse voltages.
- Confusing hole movement with electron movement: Holes are missing electrons, but they behave like positive mobile charge carriers.
- Using the exponential diode equation without unit care: \(U_{\rm T}\) must be in volts and \(T\) in kelvin.
Embedded resources
PhET: Semiconductors
Use this simulation to explore doping and the formation of a diode.
Falstad: Diode I/V curve
Use this simulation to compare a resistor characteristic with the nonlinear diode characteristic.