This is an old revision of the document!
Lab01 - Resistors -Test
Challenge description
An automotive engineer is testing the electrical system of a passenger car. The vehicle has a 12 V battery, interior lighting, a temperature sensor, and a rear window heater. During vehicle development, the engineer must verify electrical components using resistance measurements, Ohm's law, series and parallel circuits, Kirchhoff's laws, and the behavior of a non-linear load.
Resistance is defined by voltage and current:
$$ R = \frac{U}{I} $$
A constant supply voltage is available for the experiment. This raises the following questions:
- How will the different values of $U$ and $I$ influence $R$?
- How can the set of nodes help to understand the current flow?
- How will the voltage be affected from nonlinear resistors?
To answer these questions, different circuits are investigated: the Mesh-set, Set of nodes and a light bulb circuit for nonlinear resistors.
Resistance measurement
Background Information
Procedure for resistance measurement:
- Set the measuring device to resistance measurement
- Connect the resistance to be measured to the corresponding sockets on the measuring device (the measuring device sockets labeled COM and $\Omega$
- Read the measured value
There are different types of resistance measurement:
- direct resistance measurement
- indirect resistance measurement
The resistances can also be determined by measuring the current/voltage.
Ohm's law: In an electrical circuit, the current increases with increasing voltage and decreases with increasing resistance.
$$ I=\frac{U}{R} $$
Experimental Tasks
Direct resistance measurement
- task-type-result Determine the nominal and measured values of the resistance for $R_{\rm 1}$ (brown, green, orange), $R_{\rm 2}$ (yellow, violet, red), $R_{\rm 3}$ (red, violet, red) and the incandescent lamp $R_{\rm L}$. Also measure the approximate resistance $R_{\rm K}$ of your body from your right to your left hand.
- task-type-table

- task-type-freetext How do you explain the deviation between $R_{\rm L,nominal}$ and $R_{\rm L,meas}$?
- task-type-freetext What consequences can $R_{\rm K}$ have?
- task-type-freetext Now determine the series and parallel connections of resistors $R_{\rm 1}$, $R_{\rm 2}$ and $R_{\rm 3}$. \\Specify the formulas used:
- task-type-freetext $R_{\rm serial}$ =
- task-type-freetext $R_{\rm parallel}$ (= $R_{\rm a}$ || $R_{\rm b}$) =
- task-type-table

Indirect resistance measurement
Build the measuring circuit shown in figure 1 for each of the three resistors and set the voltage on the power supply to $~{\rm 12} ~{ V}$.
- task-type-result Measure $U_{\rm n}$ [V] and $I_{\rm n}$ [mA]. Calculate $R_{\rm n}$ [k$\Omega$] from these values.
- task-type-table

Mesh set
In every closed circuit and every mesh of the network, the sum of all voltages is zero!
Set the voltage on the power supply to $12~\rm V$ and measure this voltage precisely using a multimeter. Set up the measuring circuit shown in figure 2.
Add the voltage arrows and measure $U$, $U_{\rm 1}$ und $U_{\rm 2}$:
- task-type-table
<tabcaption Table-4_mesh-set_V1 | Mesh set voltage mesurement> </tabcaption>
What is the mesh set here?
Check the formula with the measured values:
The resistors $R_{\rm 1}$ and $R_{\rm 2}$ connected in series form a voltage divider.
- task-type-freetext What is the ratio between the voltages $U_{\rm 1}$ and $R_{\rm 2}$?
$$ \frac{U_1}{U_2} = $$
Set of nodes
At each junction point, the sum of all incoming and outgoing currents is equal to zero!
Set the voltage on the power supply to $12~\rm V$ and measure the voltage accurately with a multimeter. In the first step, set up the measuring circuit shown in figure 3:
Draw the arrows for the directions of currents $I_{\rm 1}$ and $I_{\rm 2}$ in figure 4. The DC current measurement range must be set on both multimeter using the rotary switch. Then measure currents $I_{\rm 1}$ and $I_{\rm 2}$ and enter the measured values in table 4.
- task-type-table
- task-type-freetext What is the relationship between currents $I_{\rm 1}$ and $I_{\rm 2}$?
$$ \frac{I_1}{I_2} = $$
Switch the power supply back on and measure the current $I$. Enter its value in table 4.
- task-type-table
- task-type-table Determine the node set for node K and check its validity.
- task-type-result Using the measured values for resistors $R_{\rm 1}$, $R_{\rm 2}$, and $R_{\rm 3}$, calculate the total resistance $R_{\rm KP}$:
- task-type-freetext Using the calculated value $R_{\rm KP}$, check the measured value of the total current:
$$ I=\frac{U}{R_{KP}} = $$
Voltage divider as voltage source
The voltage divider shown in figure 5 is in an unloaded state, as the entire current supplied by the power supply flows through the resistors $R_{\rm 1}$ and $R_{\rm 2}$ connected in series. A resistor parallel to $R_{\rm 2}$ loads the voltage divider.
Set the voltage on the power supply to $12 ~\rm V$ and measure the exact voltage with a multimeter. Set up the measuring circuit shown in figure 5.
For the connected load $R_{\rm L}$ = ${\rm 10} ~{\rm k\Omega}$, the voltage divider represents a voltage source. Like any voltage source, it has a source voltage (also called the original voltage) $U_{\rm 0}$ and an internal resistance $R_{\rm i}$. The internal resistance of a voltage divider considered as a voltage source results from the parallel connection of the divider resistors $R_{\rm 1}$ and $R_{\rm 2}$:
$$ R_i = R_1 || R_2 = \frac{R_1\cdot R_2}{R_1+R_2} $$
- task-type-result Use the measured values of resistors $R_{\rm 1}$ and $R_{\rm 2}$ to calculate the internal resistance $R_{\rm i}$ of the voltage source:
$$ R_i = $$
$$ U_0 = $$
The power $P_{\rm 0}$ supplied by the power supply can be calculated using the following equation:
$$ P_0 = U\cdot I_1$$
The power consumed by the load resistance can be determined using the following formula:
$$ P_L = R_L\cdot {I_2}^2$$
- task-type-image Draw the equivalent voltage source of the voltage divider:
- task-type-result What would be the value of $U_{\rm 2}$ without $R_{\rm L}$?
$$ U_{2, zero} = $$
- task-type-result Calculate $U_{\rm 2,L}$ and $I_{\rm 2}$ for $R_{\rm L}$ = ${\rm 10} ~{\rm k\Omega}$ using the values of the equivalent voltage source: (Provide formulas!)
$$ U_{2L} : $$
$$ I_2 : $$
- task-type-result Check the values by measuring:
$$ U_{2L, Meas} : $$
$$ I_{2, Meas} : $$ - task-type-freetext Check the values using Kirchhoff's rules: (Provide formulas!)
$$ U_{2L} : $$
$$ I_2 : $$
Nonlinear resistors
All resistors examined so far are linear resistors, for which the characteristic curve $I=f(U)$ is a straight line, s. figure 6.
The resistance value of a linear resistor is independent of the current $I$ flowing through it or the applied voltage $U$.
Fig. 6: Characteristic curve of a linear resistor
With nonlinear resistors, there is no proportionality between current and voltage. The characteristic curve of such a resistor is shown in figure 7. With these resistors, we talk about static resistance ($R$) and dynamic (or differential) resistance ($r$). The static resistance is determined for a specific operating point: at a specific voltage, the current is read from the resistance characteristic curve.
The calculation is performed according to Ohm's law:
$$ R = \frac{U}{I} $$
The differential resistance around the operating point is calculated from the current difference caused by a change in the applied voltage:
$$ r = \frac{\Delta U}{\Delta I} $$
Fig. 7: Characteristic curve of a nonlinear resistor
A light bulb is examined as an example of a nonlinear resistor. Set up the measuring circuit shown in figure 8.
Fig. 8: Measuring circuit light bulb
Set the voltage on the power supply to the voltage values from table 5. Measure the corresponding current values and enter them in table 5.
- task-type-table
- task-type-oscilloscope Create the characteristic curve $I = f(U)$, s. figure 9
Fig. 9: Characteristic curve light bulb
- task-type-result Calculate the static resistance $R$ at the operating point $U = \rm 7.0 ~V$:
- task-type-result Calculate the dynamic resistance $r$ at the operating point $U = \rm 7.0 ~V$:
- task-type-freetext Compare the values with the values from table 1 (direct resistance measurement)