This is an old revision of the document!


Lab03 - Test

You have an electric vehicle and want to charge the battery from an AC grid voltage. An on-board charger (OBC) of an electric vehicle converts AC grid voltage into DC voltage to charge the high-voltage battery.

Operating Principle:
AC Input

  • The grid provides a sinusoidal AC voltage that alternates between positive and negative values.

Rectification (Full-Bridge)

  • A full-bridge rectifier uses four diodes. During each half-cycle, two diodes conduct, ensuring that current always flows in the same direction through the load.

Pulsating DC Output

  • The output voltage is always positive but contains significant ripple at twice the grid frequency (100 Hz).

Smoothing

  • A capacitor connected in parallel to the load reduces voltage ripple by storing and releasing energy.

Active Rectification (PFC)

  • In real EV chargers, active rectifiers improve efficiency and power factor by shaping the input current to follow the voltage waveform.
2026/10/27 16:55

Resistance measurement

Procedure for resistance measurement:

  • Set the measuring device to resistance measurement
  • Connect the resistance to be measured to the corresponding sockets on the measuring device (the measuring device sockets labeled COM and $\Omega$
  • Read the measured value

There are different types of resistance measurement:

  • direct resistance measurement
  • indirect resistance measurement

The resistances can also be determined by measuring the current/voltage.

Ohm's law: In an electrical circuit, the current increases with increasing voltage and decreases with increasing resistance.
$$ I=\frac{U}{R} $$




  1. task-type-result Determine the nominal and measured values of the resistance for $R_{\rm 1}$ (brown, green, orange), $R_{\rm 2}$ (yellow, violet, red), $R_{\rm 3}$ (red, violet, red) and the incandescent lamp $R_{\rm L}$. Also measure the approximate resistance $R_{\rm K}$ of your body from your right to your left hand.
  1. task-type-table mexlefirst_public:table-1_v2.png
Tab. ##: Direct resistance measurement


  1. task-type-freetext How do you explain the deviation between $R_{\rm L,nominal}$ and $R_{\rm L,meas}$?


  1. task-type-freetext What consequences can $R_{\rm K}$ have?


  1. task-type-freetext Now determine the series and parallel connections of resistors $R_{\rm 1}$, $R_{\rm 2}$ and $R_{\rm 3}$. \\Specify the formulas used:
  2. task-type-freetext $R_{\rm serial}$ =
  3. task-type-freetext $R_{\rm parallel}$ (= $R_{\rm a}$ || $R_{\rm b}$) =
  4. task-type-tablemexlefirst_public:table-2_v1-serial_parallel.png
Tab. ##: Series and parallel connections




Build the measuring circuit shown in figure ## for each of the three resistors and set the voltage on the power supply to $~{\rm 12} ~{ V}$.

mexlefirst_public:fig-1_v1-indirect-measurement.png Fig. ##: Indirect resistance measurement

  1. task-type-result Measure $U_{\rm n}$ [V] and $I_{\rm n}$ [mA]. Calculate $R_{\rm n}$ [k$\Omega$] from these values.
  2. task-type-table mexlefirst_public:table-3_v1-indirect-measurement.png
Tab. ##: Indirect resistance measurement

Mesh set


In every closed circuit and every mesh of the network, the sum of all voltages is zero!
Set the voltage on the power supply to $12~\rm V$ and measure this voltage precisely using a multimeter. Set up the measuring circuit shown in figure ##.

mexlefirst_public:fig-1_mesh-set_v1.svg
Fig. ##: Mesh-set

Add the voltage arrows and measure $U$, $U_{\rm 1}$ und $U_{\rm 2}$:

  1. task-type-table

mexlefirst_public:table-1_mesh-set_v1.svg

 <tabcaption Table-4_mesh-set_V1 | Mesh set voltage mesurement> </tabcaption>

What is the mesh set here?



Check the formula with the measured values:



The resistors $R_{\rm 1}$ and $R_{\rm 2}$ connected in series form a voltage divider.

  1. task-type-freetext What is the ratio between the voltages $U_{\rm 1}$ and $R_{\rm 2}$?

$$ \frac{U_1}{U_2} = $$

Set of nodes


At each junction point, the sum of all incoming and outgoing currents is equal to zero!
Set the voltage on the power supply to $12~\rm V$ and measure the voltage accurately with a multimeter. In the first step, set up the measuring circuit shown in figure ##:

mexlefirst_public:fig-3_v1-node-set-1.svg Fig. ##: Node-set circuit 1

Draw the arrows for the directions of currents $I_{\rm 1}$ and $I_{\rm 2}$ in figure ##. The DC current measurement range must be set on both multimeter using the rotary switch. Then measure currents $I_{\rm 1}$ and $I_{\rm 2}$ and enter the measured values in table ##.

  1. task-type-table mexlefirst_public:fig-4_v1-node-set-2.svg

Fig. ##: Node-set circuit 2

  1. task-type-freetext What is the relationship between currents $I_{\rm 1}$ and $I_{\rm 2}$?

$$ \frac{I_1}{I_2} = $$

Switch the power supply back on and measure the current $I$. Enter its value in table ##.

  1. task-type-table mexlefirst_public:table-5_node-set_v1.svg
Tab. ##: Node set current mesurement
  1. task-type-table Determine the node set for node K and check its validity.


  1. task-type-result Using the measured values for resistors $R_{\rm 1}$, $R_{\rm 2}$, and $R_{\rm 3}$, calculate the total resistance $R_{\rm KP}$:


  1. task-type-freetext Using the calculated value $R_{\rm KP}$, check the measured value of the total current:

$$ I=\frac{U}{R_{KP}} = $$

Voltage divider as voltage source

The voltage divider shown in figure ## is in an unloaded state, as the entire current supplied by the power supply flows through the resistors $R_{\rm 1}$ and $R_{\rm 2}$ connected in series. A resistor parallel to $R_{\rm 2}$ loads the voltage divider. Set the voltage on the power supply to $12 ~\rm V$ and measure the exact voltage with a multimeter. Set up the measuring circuit shown in figure ##. For the connected load $R_{\rm L}$ = ${\rm 10} ~{\rm k\Omega}$, the voltage divider represents a voltage source. Like any voltage source, it has a source voltage (also called the original voltage) $U_{\rm 0}$ and an internal resistance $R_{\rm i}$. The internal resistance of a voltage divider considered as a voltage source results from the parallel connection of the divider resistors $R_{\rm 1}$ and $R_{\rm 2}$:
$$ R_i = R_1 || R_2 = \frac{R_1\cdot R_2}{R_1+R_2} $$

  1. task-type-result Use the measured values of resistors $R_{\rm 1}$ and $R_{\rm 2}$ to calculate the internal resistance $R_{\rm i}$ of the voltage source:

$$ R_i = $$ $$ U_0 = $$
The power $P_{\rm 0}$ supplied by the power supply can be calculated using the following equation: $$ P_0 = U\cdot I_1$$
The power consumed by the load resistance can be determined using the following formula: $$ P_L = R_L\cdot {I_2}^2$$

mexlefirst_public:fig-5-voltage-divider_v1.svg Fig. ##: Voltage divider

  1. task-type-image Draw the equivalent voltage source of the voltage divider:








  1. task-type-result What would be the value of $U_{\rm 2}$ without $R_{\rm L}$?


$$ U_{2, zero} = $$

  1. task-type-result Calculate $U_{\rm 2,L}$ and $I_{\rm 2}$ for $R_{\rm L}$ = ${\rm 10} ~{\rm k\Omega}$ using the values of the equivalent voltage source: (Provide formulas!)

$$ U_{2L} : $$

$$ I_2 : $$

  1. task-type-result Check the values by measuring:
    $$ U_{2L, Meas} : $$
    $$ I_{2, Meas} : $$
  2. task-type-freetext Check the values using Kirchhoff's rules: (Provide formulas!)
    $$ U_{2L} : $$
    $$ I_2 : $$

Nonlinear resistors


All resistors examined so far are linear resistors, for which the characteristic curve $I=f(U)$ is a straight line, s. figure ##. The resistance value of a linear resistor is independent of the current $I$ flowing through it or the applied voltage $U$.

mexlefirst_public:fig-6_linear-resistors_v1.svg
Fig. ##: Characteristic curve of a linear resistor

With nonlinear resistors, there is no proportionality between current and voltage. The characteristic curve of such a resistor is shown in figure ##. With these resistors, we talk about static resistance ($R$) and dynamic (or differential) resistance ($r$). The static resistance is determined for a specific operating point: at a specific voltage, the current is read from the resistance characteristic curve.
The calculation is performed according to Ohm's law:

$$ R = \frac{U}{I} $$

The differential resistance around the operating point is calculated from the current difference caused by a change in the applied voltage:

$$ r = \frac{\Delta U}{\Delta I} $$

mexlefirst_public:fig-7_nonlinear-resistors_v1.svg
Fig. ##: Characteristic curve of a nonlinear resistor

A light bulb is examined as an example of a nonlinear resistor. Set up the measuring circuit shown in figure ##.

mexlefirst_public:fig-8_light-bulb_v1.svg

Fig. ##: Measuring circuit light bulb
Set the voltage on the power supply to the voltage values from table ##. Measure the corresponding current values and enter them in table ##.

  1. task-type-table

mexlefirst_public:table-6_light-bulb_v1.svg

Tab. ##: Values characteristic curve light bulb


  1. task-type-oscilloscope Create the characteristic curve $I = f(U)$, s. figure ##

mexlefirst_public:fig-9_light-bulb-curve_v1.svg
Fig. ##: Characteristic curve light bulb

  1. task-type-result Calculate the static resistance $R$ at the operating point $U = \rm 7.0 ~V$:





  1. task-type-result Calculate the dynamic resistance $r$ at the operating point $U = \rm 7.0 ~V$:





  1. task-type-freetext Compare the values with the values from table ## (direct resistance measurement)